HPC/Network Access/PuTTY Configuration/The Carbon login nodes: Difference between revisions

From CNM Wiki
Jump to navigation Jump to search
m (Created page with "# In the main PuTTY Configuration window, click Session at the top of the tree on the left. # Select the '''Mega''' session and push Load. This session will be the basis for the …")
 
mNo edit summary
 
(25 intermediate revisions by the same user not shown)
Line 1: Line 1:
# In the main PuTTY Configuration window, click Session at the top of the tree on the left.
# In the main PuTTY Configuration window, click Session at the top of the tree on the left.
# Select the '''Mega''' session and push Load. This session will be the basis for the next steps.
# Select the '''Default Settings''' session and push Load.
#: [[Image:HPC 2012-08 PuTTY config 2 present.png]]
#: [[Image:HPC 2012-08 PuTTY config 2a load default.png]]
# Click SSH in the tree
# Click Data in the tree.
# '''Uncheck''' the checkbox '''Don't start a shell or command at all'''.
# Enter  your Argonne '''username''' in the Auto-login username field within the Login details section of the panel. (This step matches the one from your Mega session.)
#: [[Image:HPC 2012-08 PuTTY config 3 username.png]]
# Click "+" in front of SSH in the tree.
# Click X11 in the tree.
# Click X11 in the tree.
#* Click the checkbox '''Enable X11 forwarding'''.
#* Click the checkbox '''Enable X11 forwarding'''.
#* Set X display location to ''':0'''
#* Set X display location to ''':0'''
#: [[Image:HPC 2012-08 PuTTY config 7 X11.png]]
#: [[Image:HPC 2012-08 PuTTY config 7 X11.png]]
# Click Tunnels.
#* Select the '''L33301''' entry and push Remove. There should be no forwarded ports listed.
# Under Add new forwarded port, enter:
#* Source port: '''6200'''
#* Destination: '''mgmt03:6200'''
#* Push the Add button.
#: [[Image:HPC 2012-08 PuTTY config 8 VNL enter.png]]
# Repeat with the following settings:
#* Source port: '''6201'''  (not 6200!)
#* Destination: '''mgmt04:6200'''
#* Push the Add button.
# Repeat once more as follows:
#* Source port: '''6202'''
#* Destination: '''sched1:6200'''
#* Push the Add button.
#* You should see these three entries:
#:: L6200  mgmt03:6200
#:: L6201  mgmt04:6200
#:: L6202  sched1:6200
#: [[Image:HPC 2012-08 PuTTY config 9 VNL done.png]]
# Scroll to the top of the tree and click Session. Enter the host details:
# Scroll to the top of the tree and click Session. Enter the host details:
#* Host name: '''localhost'''
#* Host name: '''localhost'''
#* Port: '''33301'''  (referring to the tunnel set up above as L33301.)
#* Port: '''33301'''  (referring to the tunnel set up [[../The SSH Gateway|in the previous step]] as L33301.)
#* Protocol: SSH (leave at the default).
#* Protocol: SSH (leave at the default).
#* In the Saved Sessions field, enter '''Clogin'''
#* In the Saved Sessions field, enter '''Clogin'''
#* Push Save. The entry will appear in the list of saved sessions.
#* Push Save. The entry will appear in the list of saved sessions.
#: [[Image:HPC 2012-08 PuTTY config 10 Save.png]]
#: [[Image:HPC 2012-08 PuTTY config 10 Save.png]]
# '''Update 2013-02-05:''' If you wish to configure sessions for specific login nodes, Load the '''Clogin''' session, then alter these settings:
#* Port: '''33305'''
#* In the Saved Sessions field, enter '''Clogin5'''
#* Push Save.
#: and once more:
#* Port: '''33306'''
#* In the Saved Sessions field, enter '''Clogin6'''
#* Push Save.

Latest revision as of 21:18, May 30, 2014

  1. In the main PuTTY Configuration window, click Session at the top of the tree on the left.
  2. Select the Default Settings session and push Load.
    HPC 2012-08 PuTTY config 2a load default.png
  3. Click Data in the tree.
  4. Enter your Argonne username in the Auto-login username field within the Login details section of the panel. (This step matches the one from your Mega session.)
    HPC 2012-08 PuTTY config 3 username.png
  5. Click "+" in front of SSH in the tree.
  6. Click X11 in the tree.
    • Click the checkbox Enable X11 forwarding.
    • Set X display location to :0
    HPC 2012-08 PuTTY config 7 X11.png
  7. Scroll to the top of the tree and click Session. Enter the host details:
    • Host name: localhost
    • Port: 33301 (referring to the tunnel set up in the previous step as L33301.)
    • Protocol: SSH (leave at the default).
    • In the Saved Sessions field, enter Clogin
    • Push Save. The entry will appear in the list of saved sessions.
    HPC 2012-08 PuTTY config 10 Save.png
  8. Update 2013-02-05: If you wish to configure sessions for specific login nodes, Load the Clogin session, then alter these settings:
    • Port: 33305
    • In the Saved Sessions field, enter Clogin5
    • Push Save.
    and once more:
    • Port: 33306
    • In the Saved Sessions field, enter Clogin6
    • Push Save.
Retrieved from "https://wiki.anl.gov/wiki_cnm/index.php?title=HPC/Network_Access/PuTTY_Configuration/The_Carbon_login_nodes&oldid=4924"