Amiot: /* Extracting non-graphical data */

2021-06-10T20:24:44Z

Extracting non-graphical data

← Older revision		Revision as of 20:24, June 10, 2021
Line 32:		Line 32:
	==Extracting non-graphical data==		==Extracting non-graphical data==
	If LS-PrePost is to be used for extracting eg. curve data, there should be no problem using the regular "blind" prepost by		If LS-PrePost is to be used for extracting eg. curve data, there should be no problem using the regular "blind" prepost by
	setting up a command-file ~~(see [[command file]])~~ and then issuing the command:		setting up a command-file and then issuing the command:
	<pre>		<pre>
	lsprepost -nographics c=command.file		lsprepost -nographics c=command.file

Amiot: /* Getting started */

2021-02-03T18:22:31Z

Getting started

← Older revision		Revision as of 18:22, February 3, 2021
Line 19:		Line 19:
	To open a binary output file in LS-PrePost 2.4 from command line, use the command "lspp24 d3plot"		To open a binary output file in LS-PrePost 2.4 from command line, use the command "lspp24 d3plot"

	[[Image:Lspp.png\|thumb\|none\|left\|600px\|alt=LS-PrePost on TRACC Cluster\|LS-PrePost on TRACC Cluster]]		[[Image:600px-Lspp.png\|thumb\|none\|left\|600px\|alt=LS-PrePost on TRACC Cluster\|LS-PrePost on TRACC Cluster]]

	==Introduction==		==Introduction==

Amiot: Created page with "=== Getting started === Before you use LS-PrePost on TRACC cluster you will need to load module: module load ls-dyna/base To start LS-PrePost 2.4, use the command "lspp24"...."

2021-02-03T18:10:16Z

Created page with "=== Getting started === Before you use LS-PrePost on TRACC cluster you will need to load module: module load ls-dyna/base To start LS-PrePost 2.4, use the command "lspp24"...."

New page

=== Getting started ===

Before you use LS-PrePost on TRACC cluster you will need to load module:
module load ls-dyna/base
To start LS-PrePost 2.4, use the command "lspp24".

To start LS-PrePost 3.0, use the command "lspp30".

To start LS-PrePost 3.1, use the command "lspp31".

To start LS-PrePost 4.0, use the command "lspp40".

To start LS-PrePost 4.1, use the command "lspp41".

Examples:

To open an input file in LS-PrePost 3.0 from command line, use the command "lspp30 my_input_file.k"

To open a binary output file in LS-PrePost 2.4 from command line, use the command "lspp24 d3plot"

[[Image:Lspp.png|thumb|none|left|600px|alt=LS-PrePost on TRACC Cluster|LS-PrePost on TRACC Cluster]]

==Introduction==
LS-PrePost can be used for extracting data in an optimization sequence. As an optimization often needs numerous simulations<br>
to be carried out, it is preferred to use several cluster nodes which causes problems, if eg. images are to be printed showing
eg. stress distributions or such.

'''The following is referenced from http://alpha.iprod.auc.dk/wiki/index.php/Prepost_without_graphics and is valid for versions 3.x and up.'''

==Extracting non-graphical data==
If LS-PrePost is to be used for extracting eg. curve data, there should be no problem using the regular "blind" prepost by
setting up a command-file (see [[command file]]) and then issuing the command:
<pre>
lsprepost -nographics c=command.file
</pre>

where the command file could contain something like:
<pre>
ascii glstat open "./glstat" 0
ascii glstat plot 1/2
xyplot 1 savefile curve_file "./test.curve" 1 all
</pre>

==Extracting graphical data==
If you want to extract graphical data, the -nographics option will not do, as prepost needs an framebuffer / screen provided by the X-server to draw the graphics (bonus linux info at [http://en.wikipedia.org/wiki/X_Window_System wikipedia] ).<br>
This requires a little magic including a dummy framebuffer, on which the LS-PrePost graphics are then drawn and later on copied from to the output graphics file.

Linux pr default sends all its graphic program output to the display specified in the shell variable $DISPLAY. The current value of this variable can be found using the "echo" command:
<pre>
$ echo $DISPLAY
localhost:17.0
</pre>

You can save the value of the variable into another temporary variable using:
<pre>
$ export DISPLAYTEMP=`echo $DISPLAY`
</pre>
Be aware that back-tics are used on the right side! On a danish keyboard layout this is made as "shift" + the button left to backspace.

A virtual frame-buffer is started using:
<pre>
Xvfb :7 -ac -screen 0 1600x1200x24 &
</pre>
where "7" is the number of the framebuffer and "1600x1200x24" is the resolution and color depth.

The display variable is now set to the new virtual frame-buffer as:
<pre>
$ export DISPLAY=:7.0
</pre>

Prepost can now be started using a command file, as the mouse is not available as input
<pre>
$ prepost c=command.file /path/to/binaryInputFile
</pre>

When the PrePost session is over, the display variable is set back to the default value using
<pre>
export DISPLAY=`echo $DISPLAYTEMP`
</pre>

A complete shell script for a blind LS-PrePost session could then be saved to "blindpost.sh"
<pre>
DISPLAYTEMP=`echo $DISPLAY`
Xvfb :7 -ac -screen 0 1600x1200x24 &
DISPLAY=:7.0
prepost c=command.file /path/to/binaryInputFile
DISPLAY=`echo $DISPLAYTEMP`
killall Xvfb
</pre>
The "export" statement is not needed within command-files but only when executed directly from the terminal.

LS-PrePost - Revision history

Amiot: /* Extracting non-graphical data */

Amiot: /* Getting started */

Amiot: Created page with "=== Getting started === Before you use LS-PrePost on TRACC cluster you will need to load module: module load ls-dyna/base To start LS-PrePost 2.4, use the command "lspp24"...."