Run procedures: Difference between revisions

From GammaSphere DAQ
Jump to navigation Jump to search
(Removed incorrect commentary.)
 
(12 intermediate revisions by 2 users not shown)
Line 1: Line 1:
==start DAQ==
==start DAQ==


this is how you start the daq,
There are 3 controls associated with Run Control on the main page of either GUI


* first you do this
* Start/Stop - this is self explanatory. Pushing to start begins taking data.
* then you do that
* NoSave/Save - If set to Save, IOC buffers fill with data.
* and then it crashes
* and then you call Mike


Good instructions makes things easy, that is why we have none.  
 
 
To start the DGS and DFMA systems you usually do the following:
 
* on the DGS side, find the window where the DGS data is stored. There will be a start.sh script there. Start the receivers up by typing
 
  start.sh <runNo>
 
where <runNo> is the run number you want. A bunch of windows should show up, one for each receiver/IOC pair
 
* On the DFMA side, find the where the DFMA data is stored. There will be a start.sh script there. Start the receivers up by typing
 
  start.sh <runNo>
 
where <runNo> is the run number you want, the same as what you used on the DGS side please. A bunch of windows should show up, one for each receiver/IOC pair now in the FMA setup
 
* If necessary, synch the clocks of the two systems by clicking on the Impeartive sync button on the DGS side. Please don't click on the Impeartive sync button on the DFMA side or bad things will happen...
 
* now, as simultaneous as you can, click the start buttons on the DGS and DFMA DAQ windows. You shoImpeartiveuld see the receivers on both systems receiving data.
 
* may want to check that the data files are growing to be sure data is coming in
 
* check that the dssd_liveTS show the same numbers on both sides (FMA-GS-Sync) on Darek computer
 
If not : click on imp sync (GS side) but this should not happen very often
 
*Check the digitizers counters at the FMA show the same
stop runs in both sides : click on stop in the commander windows
and then stop the receivers : type Ctrl C on all the receivers (IOC1, OIC2 ....)
numbers on the left side of the window (AcEvCnt- AcHtCnt-DsCnt) and all dizitizers (right 3 raws of the window)
 
* Check the MaterDiag counters : should show numbers if the beam is on
 
* Check Sender Summary (VME SummaryDFMA window), the IOC's should keep updating at DGS


==stop DAQ==
==stop DAQ==
write your instructions here
stop the run on both sides : click on stop in the commander windows


==Changing gain in Phill's signal box==
and then stop the receivers : type Ctrl-C on all the receivers (IOC1, OIC2 ....)
write your instructions here


==Linking two or more systems==
==Linking two or more systems==
Line 39: Line 69:


'''Note:''' Clock Source cannot be set to LINK in GUI. Set address 0x8D0 in slot 0 to set 1 for trigger modules. This needs to be fixed in Driver by Tim.
'''Note:''' Clock Source cannot be set to LINK in GUI. Set address 0x8D0 in slot 0 to set 1 for trigger modules. This needs to be fixed in Driver by Tim.
==receivers==
write your instructions here
==cables==
write your instructions here
==changing FPGA Firmware code==
write your instructions here

Latest revision as of 21:27, September 20, 2023

start DAQ

There are 3 controls associated with Run Control on the main page of either GUI

  • Start/Stop - this is self explanatory. Pushing to start begins taking data.
  • NoSave/Save - If set to Save, IOC buffers fill with data.


To start the DGS and DFMA systems you usually do the following:

  • on the DGS side, find the window where the DGS data is stored. There will be a start.sh script there. Start the receivers up by typing
 start.sh <runNo>

where <runNo> is the run number you want. A bunch of windows should show up, one for each receiver/IOC pair

  • On the DFMA side, find the where the DFMA data is stored. There will be a start.sh script there. Start the receivers up by typing
 start.sh <runNo>

where <runNo> is the run number you want, the same as what you used on the DGS side please. A bunch of windows should show up, one for each receiver/IOC pair now in the FMA setup

  • If necessary, synch the clocks of the two systems by clicking on the Impeartive sync button on the DGS side. Please don't click on the Impeartive sync button on the DFMA side or bad things will happen...
  • now, as simultaneous as you can, click the start buttons on the DGS and DFMA DAQ windows. You shoImpeartiveuld see the receivers on both systems receiving data.
  • may want to check that the data files are growing to be sure data is coming in
  • check that the dssd_liveTS show the same numbers on both sides (FMA-GS-Sync) on Darek computer

If not : click on imp sync (GS side) but this should not happen very often

  • Check the digitizers counters at the FMA show the same

stop runs in both sides : click on stop in the commander windows and then stop the receivers : type Ctrl C on all the receivers (IOC1, OIC2 ....)

numbers on the left side of the window (AcEvCnt- AcHtCnt-DsCnt) and all dizitizers (right 3 raws of the window)
  • Check the MaterDiag counters : should show numbers if the beam is on
  • Check Sender Summary (VME SummaryDFMA window), the IOC's should keep updating at DGS

stop DAQ

stop the run on both sides : click on stop in the commander windows

and then stop the receivers : type Ctrl-C on all the receivers (IOC1, OIC2 ....)

Linking two or more systems

write your instructions here

syncing two systems

For DGS

  • Goto trig0 window.
  • Turn off SYNC U - listed under LRU Control
  • Make sure receive/send power is on for L & U

Note: If SYNC U is turned off - an Impeartive sync by DGS will reset the master clock on DFMA.

For DFMA

  • Goto Trig0 Window
  • Under Misc Control - turn on both undefined buttons
  • Pull up diagnotsitc window on trig0.
  • Set Clrk Source to LINK
  • Set Nim1 and Nim2 out on master trigger module FMA

Note: Clock Source cannot be set to LINK in GUI. Set address 0x8D0 in slot 0 to set 1 for trigger modules. This needs to be fixed in Driver by Tim.